Should i use resilient channel
This gap should be filled with resilient caulk, and can be finish-taped. This should also be sealed with resilient caulk. Resilient channels should be attached to the ceiling joists at right angles, as follows: mm 24 in. Type W or S screws, but never nails, to fasten channels to joists. Channels can be fastened to joists at each intersection with the slotted hole directly over a framing member, and should be installed with mounting flanges facing the same direction.
Gypsum board should be applied with long dimension at right angles to resilient channels and end joints staggered. It is best to attach boards with mm 1-in. Type S screws spaced mm 12 in. Joints between boards should be centered over the resilient channels, or be midway between channels with joints floated and backed with sections of channels.
To install resilient channels on wood- or metal-framed walls, one should attach resilient channels with the attachment flange down—except at floor level, where it should face up—and at right angles to the wall studs. A strip of gypsum panel can sometimes be used at the base of a partition in lieu of the first inverted resilient channel, and should be installed at a maximum of mm 24 in. Type W screws, rather than nails. For steel stud walls, it is important to position resilient channel at right angles to steel studs, space it mm 24 in.
Type S pan head screws driven through holes in the channel mounting flange. Channels should be fastened to studs at each intersection, with the slotted hole directly over a framing member. Gypsum board should be applied perpendicular to studs, with long dimension parallel to resilient channels.
Boards should be attached with mm 1-in. Joints between boards should be centered over the resilient channels. Where soffits are constructed, they must not support the ceiling, as this will cause the resilient channel to fail.
Soffits should be independent elements that are suspended with resilient channel. Cabinets mounted on resilient channel walls cannot be attached through to the studs, but rather must be mounted using toggle bolts to the wallboard alone. If an extra layer or more of drywall is added by the subcontractor that is above the specified assembly, the final structure weight on the resilient channel can cause the wall to touch the floor, causing a short circuit in the assembly build, subsequently creating a poorly sound insulated assembly.
Due to its weakness in strength and higher level of flexibility the single leg resilient channel compared to The first single leg resilient channel that gives us most lab test results actually no longer exists.
In USG stopped manufacturing the resilient channel that makes up most of the lab test results today that we see. Most of these results are based on sound tests conducted over 10 years ago on diverse assemblies. Resilient channel that is excessively rigid, or have holes with the incorrect dimensions or profiles, have the consequences of decreased STC ratings. A fastener is placed inaccurately or the wrong sized fastener is used.
If a fastener unintentionally makes contact with a framing member at the time of the installation of the drywall to the resilient channel, it will create a short circuited assembly and will essentially create a poorly sound insulated assembly.
Typically when attaching drywall to the resilient channels the assembly is designed to use 1-inch screws, but often installers use longer drywall screws because of ease of installation and to save time.
This is the undoing, and essentially what short circuits the resilient channel assembly. The longer screws usually are long enough to pass through the drywall, through the resilient channel and into the framing member. This is why the width between the drywall and the stud has to be correct with a decoupling product.
Thicker layers of drywall are better for soundproofing. It is also important to save space while soundproofing. So try to increase the mass without using too much space. You can find many good damping compounds in the market today. Check out my personal recommendation for damping compounds. You can use these by introducing them between the two layers being decoupled.
Damping compounds reduce the sound transmitted greatly by converting the sound energy into heat energy. The essence of decoupling is to build an air chamber. By making the insulation layer as wide as possible, greater levels of soundproofing can be achieved. But again, think about how much space you can sacrifice.
If you need that space for something else, it is better to look for other methods like the addition of an insulation layer. We can see that decoupling can help in making a room relatively soundproof. It can bring about a significant increase in the STC. But there are some drawbacks. In order to make sure that the solution is cost-effective and makes the best use of space, we can use certain devices.
In this regard, sound isolation clips and resilient channels come in handy. Though they are both effective, it has been found that sound isolation clips perform better and can be used more easily than resilient channels.
Soundproofing depends on four elements — absorption, damping, decoupling, and mass. But by paying attention to these four factors, a room can almost be soundproof. It moves from one point to another by transferring its energy to particles. These particles sort of relay the energy by vibrating. This sort of energy transfer helps sound travel.
It is possible to prevent sound from traveling by trapping it in an insulated chamber. Think about it, if the city has no roads, you cannot drive your car. Similarly, without a medium, sound cannot travel. Remember the astronaut in space jokes? The punch line is that an astronaut cannot hear anything on the moon because it has no atmosphere.
0コメント